How to Install a Ghost Immobiliser

Ghost immobilisers are hidden security device that protects your vehicle from hacking and key cloning. It works by stopping the vehicle’s engine from starting until it is started with the PIN code that can be as long as 20 characters.

It is unnoticeable by thieves and they are unlikely to expect this extra layer of security. Certain systems come with an app which allows the owner to disable their immobiliser if they forget their PIN number or utilize the service/valet mode.

Connecting to the vehicle’s CAN bus

The Ghost 2 Immobiliser is a cutting-edge security system that can be integrated into your vehicle’s ECU and provides a discrete protection against thieves. It is extremely efficient and user-friendly and is a great addition to your vehicle’s security arsenal. However, just like any other anti-theft device, it is not impervious to failure and requires regular maintenance to ensure proper operation. Fortunately, this guide will help you get the most benefit from the Ghost 2 Immobiliser.

CAN (Controller Area Network) is a reliable serial networking system that lets microcontrollers communicate with each over short distances. A central control unit is not required. It is designed to multiplex electrical wiring inside vehicles to save on copper and offers a range of advantages, including low costs and a simple use.

The CAN protocol is utilized in the majority of modern automobiles to connect with the engine management system, steering control module, air conditioning controls, and more. It also relays information from sensors like speed sensors, as well as other inputs, to regulate the car’s various features. The CAN bus is used to monitor these various components, and it can stop the car from starting if they’re in an unsafe state.

While the CAN bus can be utilized for a variety of purposes, it’s crucial to know how it functions and how it’s secured. The CAN bus is an excellent method to add new features to your vehicle, but it’s essential to secure it from hackers and other threats. Installing a firewall and monitoring your CAN bus with software is the best method to accomplish this.

Ghost2’s control unit is hidden in the car’s dashboard or wiring harness, which prevents an intruder from physically altering it. It is also impossible to reset the PIN or emergency code without access to the vehicle.

If you must give your car away for servicing, valet parking, or any other reason, you can use the Transport Mode. This feature disables both the keyfob and ignition functions of the Ghost immobiliser. It will only be activated when the vehicle has reached 31 mph for a time of 15 minutes.

Creating a PIN code

The Ghost immobiliser is a robust security system that protects your vehicle from theft. The innovative technology uses a PIN to disable the engine of the vehicle and stop it from starting without the right code, or a valid fob or mobile. The system’s discrete design makes it unnoticeable, and offers unrivaled security against theft. Moreover the system is TASSA verified and can lead to significant savings on insurance premiums for cars.

During installation, Ghost enters a “learning mode” to record the sequence of buttons that are pressed to create unique pin codes. The installer will guide you through activating the system after the pin code is created. Once activated it will Ghost system will turn off the starter motor of your vehicle unless a valid PIN is entered or the vehicle is switched into transport mode. This makes it extremely difficult for thieves to copy or hack your vehicle’s starting system.

It is easy to install an easy-to-install Ghost immobiliser, but you must follow the precise instructions included in the user guide to ensure the proper operation. Hand tools and multimeters can be used to check electrical values. Insulation tape and heat shrink tubing can protect the exposed wiring and cable ties are essential for keeping everything neat and secure. Also, be sure to test the system regularly to identify any problems and potential errors.

Once the installation is complete it is crucial to conduct a final test of the system prior to turning on your vehicle’s ignition. Ghost immobilisers will arm themselves after a period of 3 to 30 seconds depending on the model of your vehicle. The system is also equipped with a Service/Valet Mode that allows you to temporarily disable the system for servicing or valet parking.

Ideally, the immobiliser should be placed in a discreet location beneath the dashboard or steering wheel. It is recommended to use a small piece of duct tape or paint to mark the CAN H and L wires, so that you can easily find them during testing. The CAN H and the L wires should be connected to an electrical source that provides an uninterrupted 12V. It is important to check the connections again after testing as the incorrect identification of these wires could cause the system to malfunction.

The system must be activated

A ghost immobiliser stops your car from starting until you press certain buttons in the vehicle, usually on the steering wheel, the door panel or the central console. The sequence can be altered by the user in case it is needed. Once the system is activated it cannot be deactivated by thieves which makes it a great option for anyone who wishes to safeguard their vehicle from theft.

The device is not designed to be able to be detected by modern diagnostic tools and code-grabbing technologies. It also doesn’t broadcast radio signals which makes it difficult for thieves to identify the device.

If the device is identified, it will stop the engine from starting and sound an alarm that is loud enough to scare away the thief. The device can be used to track a car’s location and assist in the recovery of the vehicle in case it was taken.

Contact Car Specalist Customs for a quote or to discuss your options in an immobiliser that is ghost-like. We are fully trained to install a ghost immobilise r to your vehicle, and will make sure that it is tucked away in a remote area. We can also provide other security measures, such as an ignition lock for your wheel and a kill switch to keep your car safe from thieves.

Disarming the system

It is important to know how to deactivate a Ghost immobiliser if it is installed in your vehicle. This will assist you in the case that you lock your keys inside the car or when your battery goes out of. The system utilizes a unique PIN code, which only you are aware of. It cannot start the vehicle without this code. The easiest way to enter the code is to press a set of buttons on your dashboard or the steering wheel. This is much easier than using a key fob and prevents others from copying the remote.

Unlike some aftermarket immobilisers that require cutting wires to install, Ghost2 is non-invasive and works with your vehicle’s CAN bus network to operate. Its most notable feature is its ability to bypass the engine without affecting the normal functions, making it hard for thieves to use signal boosters or clone your car key. Additionally, it doesn’t emit radio frequencies, meaning thieves aren’t able to detect the system.

The Ghost system comes with an option called Transport Mode that allows you to temporarily disable security in situations such as transportation or service. This is a great option when you need to lend your vehicle to someone without sharing the PIN code or if you want to ensure your vehicle is secure while driving it. To activate ghost immobiliser 2 , press the service button 5 times within a period of 2 seconds. The Ghost system will confirm activation by giving 5 signal indicators.

When you’re done, remember to save the emergency code in a safe location outside of your vehicle. If you happen to find yourself locked out of your vehicle, you’ll be able to contact the technician or the company that installed the system and they’ll provide you with the code. If you are unable to reach them, you can always try to contact an authorized dealer but this would require verification procedures and could incur additional charges.

This system isn’t just convenient, but it can also protect your vehicle from theft and reduce insurance costs. Many insurance companies offer lower rates or financial incentives to install this anti-theft system.